Sewage Ejector Pump Design

shutterstock_1049493110

Detailed

We make sure to pay close attention to details as possible in order to create a well-detailed and comprehensive design.

shutterstock_1049493110

Efficient

Our designs are all geared towards maximum efficiency not just in terms of performance but energy savings as well.

shutterstock_1049493110

Long Lasting

We also make sure that our designs are made to be durable and long-lasting, saving you tons of money in hefty replacements and renovations.

Get In Touch

Sewage Ejector Pump Explained

 

Sewage Ejector Pumps

A sewage ejector pump, likewise known as a pump up ejector system, is often applied on rooms or fixtures which are below the main sewer of any building. Since sewage systems rely on gravity to drain all of the accumulated wastewater, fixtures which are located below the sewer line will have to use on another means to allow wastewater to drain properly.

 

That’s exactly what we at New York Engineers try to accomplish. By creating detailed and efficient sewage ejector pump designs, we will be able to provide an efficient method to drain away all wastewater located below your lines at all times. Regardless of the type of building you have, whether it be a commercial or residential property, we will tailor our designs to fit your needs.

 

If you are having problems with the poor drainage system in your building, then one of the main culprits is a poor and inefficient pump design. This is where our sewage ejector pump design service enters the picture.

 

Sewage Ejector Pump Explained

 

A sewage ejector pump is considered a submersible solid handling pump which operates on low pressure and high volumes. Compared to other types of pumps, a sewage ejector pump doesn’t have any grinding blades. Instead, it uses a spinning mechanism which takes sewage through the bottom then forces it out using pressure into the discharge pipe.

 

In most cases, an ejector pump is installed in buildings that have a bathroom located in the basement. It’s not required in all basements, but when the sewer lines are located at a higher elevation than the fixtures, this is where it will come in handy.

 

This type of pump is also used in rural applications, particularly in septic drain-field systems. Regardless of the application, having a well-designed ejector pump is highly necessary to ensure proper wastewater flow and disposal. As such, our expert designers and engineers make sure to assess your project so they can formulate and tailor a custom design to fit your needs.

 

How We Create Our Designs

 

A sewage ejector pump is a highly crucial component on your building if you have wastewater situated in below-ground areas. Though it’s not really hard to install, there could be times where some problems could occur during the construction phase.

In this case, we at New York Engineers will help you with the designing process to make sure that there will be little to no errors during your construction project. To give you an idea, here’s how we create our designs:

  1. As a standard operating procedure, whenever you give us a call and avail of our design services, we will discuss with you the full scope of your project. As much as possible, we’d like you to provide us with the complete information regarding your building, current budget, specifications, and the likes. The more accurate the information you give us, the easier it will be for us to create a working design based on your needs.

  2. Once we come to an agreement regarding your project and budget, we will then send our inspection team to perform a full inspection of your building, specifically the sewage system. This way, we will be able to create a sewage ejector pump design that will fit with your current system. Since the way each sewage system varies depending on the blueprint of a building, it won’t be possible for us to create a custom design without performing inspections.

    During this stage, our inspection team will also ask additional questions and request additional information regarding your project.

  3. After we have gathered all of the details we need, we will then proceed with the design. In this stage, we will leave the work to our expert designers and engineers. They will be the ones to come up with a foolproof design based on your specifications and other important data.

    Before they start with the design, they will first brainstorm ideas and come up with design concepts. After that, they will then start voting which among the design is the most practical and functional.

    At New York Engineers, we only make use of the latest tools and software such as Revit and AutoCAD which are considered the standards in the MEP design and BIM industry. We also make sure that our methods and techniques are updated so we can keep up with the changes and trends in the industry. 

  4. After we have come up with an initial design, we will then send it to you. Take note that the initial design we send is not yet final. In this stage, we will be asking for your initial feedback so we can make appropriate revisions in the design. Also, as much as possible, we would like you to collaborate with us by giving us information about which certain components you want added or removed.

    This way, we will be able to come closer to a finished product without missing any important detail. You have the option to visit us on-site to personally collaborate with us. Alternatively, you can also give us a call and give us all the details regarding your feedback.

  5. Once you have reviewed the initial design and given us your feedback, we will then proceed with the polishing. This is where our designers and engineers get rid of any errors and design flaws which might be present. This is also where we polish the design to make it final.

  6. After we have finalized the design, we will then inform you about it. We can also simulate your design in a 3D environment so you can have a preview of how the design will look like in actual setting once it’s constructed and installed.

  7. Once you have approved of everything, we will then send you the final design. Since we have a very high approval rate, we are confident that you will be satisfied with our design. Also, since we have worked with many sewage ejector pump design projects before, we are highly knowledgeable when it comes to this type of work.

Get Pricing On a New MEP Design Proposal in Fewer than 24 Hours

Request a proposal →

Our Design Considerations

 

sewagemanhole

Apart from detailed and quality designs, we at New York Engineers also take into account certain design considerations to make sure that your construction project is a success. 

 

Before we create the designs for your sewage ejector pump, we first make sure that we check the local building department in your area. If you’re from Chicago, you can rest easy as we are already well-versed with all the building codes and requirements in the city.

 

However, if you’re from another city, it will also be the responsibility of our inspection team to check the local building codes within the area. We know that any work which involves sewer lines will most likely require a permit, and it’s just proper considering that poor design and installation can make a huge mess.

 

Another important factor we consider when designing your ejector pump is its size. Pumps normally come in a variety of sizes and horsepower, and the basins have varying hold capacities as well. That said, if you’re planning to have the pump installed in a residential building, then we’d opt for a standard pump size and basin capacity. Commercial buildings, on the other hand, will require a larger one. 

 

Keep in mind that a standard ejector pump kit will cost you around $400 to $1,000 on average. This means that any repair or replacement can be quite costly. As such, you have to make sure that you don’t have to resort to such expenses. Our quality and durable ejector pump designs will help you with that. 

 

Why Design Your Ejector Pump?

 

You already know that a sewage ejector pump is important for removing wastewater in rooms that have fixtures below the main sewer line. Unfortunately, not all sewage ejector pumps you can buy on the market work efficiently. Due to this, designing your own ejector pump can be quite beneficial.

With a well-designed ejector pump, you can enjoy the following:

  • Clog-free pipelines
  • Reduced risks of flooding which can be due to burst pipes
  • Reduced chances of sewage water entering your taps and sinks
  • Reduced risks of diseases brought on by sewage water

 

The above benefits apply to all buildings regardless if it’s for a commercial or residential setting. With a proper wastewater flow brought on by a well-designed ejector pump, you won’t have to face sewage issues which can affect everyone inside the building.

 

Why Choose Us?

 

At New York Engineers, we guarantee that your design is in good hands. After all, we’re not just about quality designs, we’re also all for efficiency, cost-savings, and durability. That said, here are the main reasons why you should start working with us:

 

  • Experienced and Knowledgeable Professionals

One of the main reasons why we are able to provide high-quality design services to our clients is because our team is made of professionals who have years of experience and knowledge in the industry. Aside from that, despite the years of knowledge backing us, we are still continuing to learn the latest methodologies and trends to help us stay updated with the developments in the MEP industry.

 

  • Friendly and Approachable Team

Aside from being professionals who are ready to take on your projects, our staff here at New York Engineers are also very friendly. As such, you can expect to approach them if you have any concerns or inquiries you want addressed. They will do their best to help you with your queries and make sure that they are resolved accordingly.

 

  • Latest Tools

 To ensure that we can create quality and accurate designs, we make sure to use only the latest tools and software in the MEP industry. This means that our designs are all up-to-date with the innovations and various other standards. 

 

  • Smooth Process

Our design service always follows a smooth standard operating procedure. This way, we can always have a systematic approach to how we do your design. This gets rid of any hurdles along the way and make sure that the final output is delivered to you without any hassle.

 

  • Quick Turnaround Time

We understand that any construction project has its time constraints. Due to this, we make sure that we can deliver your project way before your deadline. However, while doing so, we make sure we won’t compromise the quality of our work, otherwise, it could only result in a revision which, in turn, can only delay your project even further.

 

  • Accurate and Error-Free Designs

Since we will be sending you the initial design for initial feedback, we will be able to eliminate any errors and do appropriate revisions based on your feedback. However, do take note that we will also be giving design recommendations to ensure that you only get a highly efficient design.

 

  • Affordable Services

Lastly, our sewage ejector pump design service, alongside other design services, are offered at very affordable rates. This way, you won’t have to spend a lot of cash just to have an efficient and durable design. We know how costly an ejector pump can be, much more if it’s a custom-made one based on a custom design. 

Looking for an MEP / Fire Protection Engineering Poject?

Contact Us →

New York Engineers – Your Go-To Team for Efficient Designs

 

Group of engineers working at a construction site

At New York Engineers, we always make sure that we can give you, our customers, only the best service at the most affordable rates possible. If you’re looking for a highly efficient ejector pump design that will last for years, allow us to help you. 

 

Aside from sewage ejector pumps, we also offer other design services in the field of manufacturing, engineering, and plumbing. If you want custom industrial designs, don’t hesitate to give us a call or contact us through our Contact page.

 

You can also visit us in one of our branches in New York, Chicago, and New Jersey.

 

We’ll be waiting for your call!

Agencies Approvals We Secure

Have an MEP Engineering Project? Talk To Us.

 

"Thank you Jahnavi and team for all of your dedication and hard work on this important project for HANAC and the Corona Community."

John-Napolitano_48x48 John Napolitano, Director of Capital Projects, HANAC

"Things went well, and I want to restate how much I appreciate the Herculean effort your team provided to finish up by today!"

Murray-Levi_48x48 Murray Levi, Principal, MTA Artchitects

"The way we work together, the way they overcome challenges, and the way they deliver impresses me more than other engineers, and I'm one of them!"

Silviu-Herscher_48x48 Silviu Herscher, Director of Capital Infrastructure, The New School